MAP – GM 3 Bar MAP Sensor Uncrimped Connector by DIYAutoTune - We include an extra pin and weatherseal just in case you need it as well. Needed to go along with that gm 3 bar map sensor you just dropped in your cart ).
Optical Trigger Wheel for Nissan SR20DET or KA24DE by DIYAutoTune - Intended for use with ms1 and ms2. Convert your nissan cas to a more megasquirt-friendly arrangement with our bolt in optical shutter wheel. This one replaces the ring of four slits with a 24-1-1 wheel that behaves like a 12-1 crank trigger. You can use just the inner ring to get a rapid sync-up, or use the outer slot to allow for sequential injection or coil-on-plug. We added an outside slot to provide a cam sync where the 360 degree slot ring works.
JimStimX Expansion Board – Assembled by DIYAutoTune - See the inputs and outputs on the ms3x expansion card in action. Use the three pull-off jumpers on the jimstim to connect the 5 volt power, ground and cam signal to the jimstimx. Requires a jimstim for proper operation, sold separately. Fully assembled and ready to plug in to your ms3x.
4 Position Flat Weather Pack 3-pack – 20 to 18 Gauge Delphi Weatherpack by DIYAutoTune - Genuine delphi parts. (26) 20 to 18gauge seals. 13 male and female 20-18 gauge pins. Enough pins and seals to do your project right. 3 male and female connectors.
6 Tower Wasted Ignition Spark Coil Pack Without Ignitor DIYAutoTune - Use with hei type plug wire boots. This coil can deliver up to 58 mj per spark if you have a hot enough ignition module to drive it. Coil also has a handy set of plug wire numbers stamped on it. Need a connector uses ign_6_wpk connector. Looks can be deceiving.
22 Position Delphi Weather Pack Connector Kit by DIYAutoTune - Use this giant 22 position weather pack connector to run wires through a firewall or as a quick disconnect for your engine harness, or other components that need a lot of wires. Includes (1) 22 position male and female connector, (13) 20-18 gauge male and female pins, (13) 16-14 gauge male and female pins, (4) 12 gauge male and female pins, (26) 20-18 gauge seals, (26) 16-14 seals (8) 12 gauge seals, (8) plugs, (4) comb locks. To get this one through the firewall, you’ll need a 2 1/16″ hole. Genuine delphi part. It’s a bit of an odd size, but the same size as many aftermarket gauges. The built in gasket ensures a tight seal.
IAC Valve Pigtail (6″) by DIYAutoTune - More informationpart number for the valve niehoff part# 21774 (this is what was used in all testing)oem application of this valve 1992 jeep cherokee w/ 4. 0l inline 6 (among many others). This is the wiring pigtail to compliment darkstar’s iac valve body complete with detailed assembly instructions (it’s super easy- basically just plug them in) so that you can color code the wiring depending on how you wire your iac valve.
755 Piece Weather Pack Kit Delphi Weatherpack by DIYAutoTune - More than enough crimp terminals to get the job done right. Several different sizes to ensure the connection is as secure as possible. 1-6 position connectors which breaks down to (4 each) 6 position m/f (3 each) 5 position m/f (6 each) 4 position m/f square (5 each) 4 position m/f flat (6 each) 3 position m/f (6 each) 2 position m/f (6 each) 1 position m/f. 755 pieces genuine delphi parts. 20-12 gauge pins and seals which breaks down to (70 each) 20-18 ga m/f (70 each) 16-14 ga m/f (23 each) 12 ga m/f (140) green 20-18 ga seals (140) gray 16-14 ga seals (46) blue 12 ga seals (30) plugs (1) terminal pin removal tool.
QuadSpark Four Channel Ignition Module by DIYAutoTune - 6″ wiring pigtail you can solder or crimp to your wiring harnesses. Off the shelf ignition module suitable for underhood mounting that can drive four coils, handle plenty of current, and doesn’t cost a fortune. Use with oem distributorless ignitions that don’t have the ignition module built into the coil. Perfect for running our ign-1, ign-1fd, ign-4, or ign-6 coils.
3 Position Weather Pack 3-pack – 20 to 18 Gauge Delphi Weatherpack by DIYAutoTune - 10 male and female 20-18 gauge pins. Genuine delphi parts. (20) 20-18 gauge seals. Enough pins and seals to do your project right. 3 male and female connectors.
Weather Pack 12 Gauge Terminal Pins – 30 pack Delphi Weatherpack by DIYAutoTune - For 12 gauge wire. Package contains 30 pairs of male and female weather pack terminals. Plus 60 blue seals. Genuine delphi parts.
4 Position Square Weather Pack 3-pack – 20 to 18 Gauge Delphi Weatherpack by DIYAutoTune - 3 male and female connectors. Enough pins and seals to do your project right. 13 male and female 20-18 gauge pins. Genuine delphi parts. (26) 20-18 gauge seals.
GM Boost Control Connector w/ crimp-on pins by DIYAutoTune - This connector comes with crimp-on pins to keep the number of splices in your wiring harness to a minimum. Weatherpack-style connector for gm boost control solenoid. We continue to offer these connectors for customers that need them for their gm style valves, and other gm solenoids and sensors that use the same connector as this was a fairly common connector under gm hoods. Note this connector is not needed for our newer style (12/2008 and newer) non-gm ebc solenoid.
2 Position Weather Pack 3-pack – 16 to 14 Gauge Delphi Weatherpack by DIYAutoTune - (14) 16-14 gauge seals. Genuine delphi parts. 7 male and female pins. 3 male and female connectors. Enough pins and seals to do your project right.
4″ 36-1 Trigger Wheel by DIYAutoTune - 4″ in diameter and 1/8″ thick, with a 1/2″ diameter center hole. Laser cut 36-1 crank trigger wheel. This trigger wheel has a balance hole in it for smooth rotation. Fits crankshaft pulleys up to 3 1/2″ in diameter. Designed for imports with unusually small trigger wheels.
IAC Valve Connector by DIYAutoTune - Comes with the connector, four pins, plus an extra pin (just in case). Iac valve connector (uncrimped).
DIYBOB Breakout Board Kit for Nippondenso 52 Pin Connector by DIYAutoTune - This one fits cars with a 52 pin nippondenso ecu. Easily build professional looking adapter harnesses to connect the engine management of your choice. The diybob includes an oem style connector, circuit board, and an anodized aluminum case. The diybob is a new breakout board from diyautotune. Works for many cars, including the ’90-’94 mitsubishi eclipse and most ’86-’90 toyota supras.
Weather Pack 16 to 14 Gauge Terminal Pins – 30 pack Delphi Weatherpack by DIYAutoTune - Genuine delphi parts. For 16 to 14 gauge wire. Package contains 30 pairs of male and female weather pack terminals. Plus 60 gray seals.
4 Position Square Weather Pack 3-pack – 16 to 14 Gauge Delphi Weatherpack by DIYAutoTune - 3 male and female connectors. Enough pins and seals to do your project right. Genuine delphi parts. 13 male and female 20-18 gauge pins. (26) 16 to 14 gauge seals.
Connector with Pins for IGN-4 Coil Pack by DIYAutoTune - Crimp connector and pins for ign-4 coil. This is a standard “junior timer” sort of connector. Other uses such as bosch crankshaft position sensors and throttle position sensors.
460 Piece Weather Pack Kit Delphi Weatherpack by DIYAutoTune - More than enough crimp terminals to get the job done right. 460 pieces, genuine delphi parts. (6) male and female 1 position connectors (6) male and female 2 position connectors (6) male and female 3 position connectors (6) male and female 4 position square connectors (5) male and female 4 position flat connectors. (40) 20-18 gauge female pins (40) 20-18 gauge male pins (40) 16-14 gauge female pins (40) 16-14 gauge male pins (15) 12 gauge female pins (15) 12 gauge male pins (80) green 20-18 gauge seals (80) gray 16-14 gauge seals (30) blue 12 gauge seals (21) plugs (1) terminal removal tool. Several different sizes to ensure the connection is as secure as possible.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.